Nordictrack futura 2200 manual

Cart Shopping Cart 0 item s in your cart. Restore a saved shopping cart. NordicTrack Home Gym Parts. Preferred Partners of. Continue Shopping Proceed to Checkout. Search within model. Page A. Add to Cart. Popular Parts. M10 Washer. M8 Nylon Locknut. M6 Large Washer. M10 X Mm Button Screw.

M8 Washer. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton.

This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly requires the included allen wrench and your own phillips screwdriver , adjustable wrench , and rubber mallet. For help identifying the assembly hardware, see the drawings below. The number following the parentheses is the quantity needed for assembly.

Note: Some small parts may have been pre-assembled. If a part is not in the parts bag, check to see if it has been pre-assembled. To avoid damaging plastic parts, do not use power tools for assembly. Attach the four Base Pads 81 to the base of the Uprights. Note: One replacement Base Pad may be included. Use the Base Pad to replace any Base Pad that becomes worn. With the help of a second person, carefully tip the treadmill down so the four Base Pads 81 are resting on the floor and the Uprights 85 are in the vertical position.

Remove the band securing the Upright Wire Harness 73 to the right Upright Have a second person hold the console assembly near the right Upright. Connect the Upright Wire Harness 73 to the wires extending from the console assembly. Make sure to connect the connectors properly see the inset drawing. The connectors should slide together easily and snap into place.

If the connectors do not slide together easily and snap into place, turn one connector and try again. IF THE. Insert the connectors into the right Upright With the help of a second person, set the console assembly on the Uprights Make sure that no wires are pinched.

Attach the console assembly with four Console Bolts 72 and four Star Washers 67 only one side is shown. Start all four Console Bolts before tightening any of them. Remove the knob from the pin. Make sure that the collar and the spring are on the pin. Press the Latch Insert 77 into the right side of the left Upright 85 , and press the Knob Insert 92 into the left side of the left Upright. Use a rubber mallet, if necessary. Next, insert the pin into the Latch Insert, and tighten the knob back onto the pin.

Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen wrench in a secure place; the allen wrench is used to adjust the walking belt see page If you purchase the optional chest pulse sensor see page 22 , follow the steps below to install the receiver included with the chest pulse sensor.

Make sure that the power cord is unplugged. Connect the wire on the receiver A to the indicated wire extending from the Console Back Hold the receiver so the small cylinder is oriented as shown and is facing the Console Back. Attach the receiver to the plastic posts on the Access Door 95 with the two included small screws. Reattach the Access Door 95 with the Screw Discard the other wires included with the receiver. Your treadmill features a walking belt coated with highperformance lubricant.

Such substances will deteriorate the walking belt and cause excessive wear. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product—if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Voltage surges, spikes, and noise interference can result from weather conditions or from other appliances being turned on or off.

To decrease the possibility of your treadmill being damaged, always use a surge suppressor with your treadmill see drawing 1 at the right. To purchase a surge suppressor, see your local NordicTrack dealer or call the toll-free telephone number on the front cover of this manual and order part number , or see your local electronics store. The surge suppressor must have a UL suppressed voltage rating of volts or less and a minimum surge dissipation of joules.

The surge suppressor must be electrically rated for volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate whether it is functioning properly. This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of elec-. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug.

Plug the power cord into a surge suppressor, and plug the surge suppressor into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. This product is for use on a nominal volt circuit, and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that looks like the adapter illustrated in drawing 2 may be used to connect the surge suppressor to a 2-pole receptacle as shown in drawing 2 if a properly grounded outlet is not available.

Grounded Outlet Box. Surge Suppressor. The temporary adapter should be used only until a properly grounded outlet drawing 1 can be installed by a qualified electrician.

The green-colored rigid ear, lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used it must be held in place by a metal screw. Some 2-pole receptacle outlet box covers are not grounded.

Contact a qualified electrician to determine if the outlet box cover is grounded before using an adapter. The treadmill console offers an impressive array of features designed to help you get the most from your workouts.

When the manual mode of the console is selected, the speed and incline of the treadmill can be changed with the touch of a button. As you exercise, the console will display continuous exercise feedback. You can even measure your heart rate using the builtin handgrip pulse sensor or the optional chest pulse sensor see page In addition, the console features eight preset programs.

Each program automatically controls the speed and incline of the treadmill as it guides you through an effective workout. Next, insert the key into the console. Page 14 When you are finished exercising, remove the key.

Step onto the foot pads, press the Stop button, and adjust the incline of the treadmill to the lowest setting. The incline must be at the lowest setting when the treadmill is folded to the storage posi- tion or the treadmill will be damaged.

Page 16 When the program has ended, make sure that the incline of the treadmill is at the lowest set- ting. Next, remove the key from the console and put it in a safe place. If this occurs, see the instructions included with the optional chest pulse sensor. See pages 18 and 19 for connecting instructions.

To use iFIT. Page 21 Stop button or remove the key and go to step 1 on page Page 22 Additional options are soon to be available. See www. To use programs from our Web site, the treadmill must be connected to your home computer.

In addition, you must have an internet connection and an internet service provider. The information mode also al If this is not done, the treadmill may be per- manently damaged. Remove the key and unplug the power cord. Hold the upper end of the treadmill with your right hand as shown. Using your left hand, pull the latch knob to the left and hold it.

Pivot the frame down until the walking platform is past the pin on the latch knob. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. Page 27 4 inches off the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, in- sert the key, and run the treadmill for a few minutes.

Repeat until the walking belt is properly tightened. If the walking belt still slows when walked on, please see the front cover of this manual.