Lf-pk1 download

Preparations Station Base. You will need this information when you set up the base station and make wireless connections. Install the base station so that you can easily see the side panel. With the stand positioned so that the section labeled as FRONT is toward the front of the base station, insert the claws of the stand in the holes on the bottom of the base station and slide the stand toward the back of the base station to lock it into place. The procedure for connecting to a TV antenna depends on the type of antenna jack.

Some antenna jacks require a separate converter or splitter not supplied. For more information, contact your Sony dealer. Select [Video 1] in the [Index] window. You can operate the connected device using the on-screen remote control. Open the [Index] window, select [Video 1] or [Video 2] according to the input terminal to which the device is connected.

For details, see the next page. Connect the DVD player directly to the video input terminal on the base station. With reference to the operating instructions of the device, make sure to place the IR Blaster just above the infrared receiver.

After configuring LocationFree Player remote control settings 1 page 30 , remove the backing paper from the IR Blaster and fix it in place. For details on setting up a device, refer to the operating instructions of the device. If the infrared receivers on the two devices do not line up like the picture above, you cannot control them with the single supplied IR Blaster, and you need to purchase a plug adapter PCM, not supplied and another IR Blaster.

These on-screen remote controls allow you to operate two devices connected directly to the base station, and to control video input via those devices.

Connections and Setup. You can also make base station settings via a wireless connection. Also, a wireless LAN uses a channel in the 2. The base station is still in setup mode after this 5-minute state. It could cause interference while watching TV. Connectionsand Setup. If your router is configured to assign IP addresses by a DHCP function, and your computer is set to [Obtain an IP address automatically], then you can connect simply by connecting the computer and base station with a LAN cable.

If it is off, make sure the router is on and the LAN cable is connected properly. To make a wireless connection between a computer and the base station, set up the wireless network connection of the computer. For details, refer to the operating instructions for your computer and wireless LAN devices, such as a wireless LAN card. Before you register your computer with the base station and display TV on the computer, you need to install LocationFree Player on the computer 1 page When using a router to connect to the base station, it takes a while for the IP address to be assigned to the base station by DHCP.

The base station does not appear in the window shown in Step 2 until the IP address has been assigned. You can change the nickname on the screen that appears if you click [Properties]. This step explains how to set up your network to connect to your base station at home via public wireless LAN networks and hotel LAN connectors. To watch TV and videos away from home, you must first connect the base station to the Internet. Contact your Internet service provider for more information about the speed of your communications line.

The connection method you should use depends on your ISP and equipment. For more information, contact your ISP. For more information, contact your service provider. If you have any questions, contact your service provider. When connecting a computer to the base station using a router 1 page 14 , set the base station to setup mode 1 page You can also use the [Start] menu. If LocationFree Player is already running, disconnect by clicking [Disconnect] in the lower left of the window, then click [Connect] again.

Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Make sure that you can easily see the side panel after installing the Base Station.

You will need this information when you set up the Base Station and make wireless connections. With the stand positioned so that the section labelled as FRONT is toward the front of the Base Station, insert the claws of the stand in the holes on the bottom of the Base Station and slide the stand toward the back of the Base Station to lock it into place.

Select [Video 1] in the [Index] window. You can operate the connected device using the on-screen remote control.

Open the [Index] window, select [Video 1] or [Video 2] according to the input terminal to which the device is connected. For details, see the next page. With reference to the operating instructions of the device, make sure to place the IR Blaster just above the remote sensor. After configuring LocationFree Player remote control settings 1 page 28 , remove the backing paper from the IR Blaster and fix it in place. For details on setting up a device, refer to the operating instructions of the device.

If the remote sensors on the two devices do not line up like the picture above, you cannot control them with the single supplied IR Blaster, and you need to purchase a 3. These on-screen remote controls allow you to operate two devices connected directly to the Base Station, and to control video input via those devices. Connections and Setup. Security Level: Low ] 1 page The Base Station is still in setup mode. POWER button. If it is off, make sure the router is on and the LAN cable is connected properly.

To make a wireless connection between a computer and the Base Station, set up the wireless network connection of the computer. For details, refer to the operating instructions for your computer and wireless LAN devices, such as a wireless LAN card. Before you register your computer with the Base Station and display video on the computer, you need to install LocationFree Player on the computer 1 page The Base Station does not appear in the window shown in Step 2 until the IP address has been assigned.

Player icon on the desktop of the computer. You can also use the [Start] menu. If your Base Station does not appear on the [Base Station Selection] screen, your security software or browser may be blocking the communication between the LocationFree Player and the Base Station. Refer to the instruction manuals of your security software or the online help of your browser to configure them not to block the communication. The Base Station is restarted automatically after registration. Wait for a while until a connection is established with the Base Station.

To configure the on-screen remote control and the colour system, go to page You can change the nickname on the screen that appears if you click [Properties]. This step explains how to set up your network to connect to your Base Station at home via either wireless or wired public Internet access.

To watch video away from home, you must first connect the Base Station to the Internet. Contact your Internet service provider for more information about the speed of your communications line. The connection method you should use depends on your ISP and equipment. For more information, contact your ISP. For more information, contact your service provider.

If you have any questions, contact your service provider. If the LocationFree Player is already running, disconnect by clicking [Disconnect] in the lower left of the window, then click [Connect] again.

Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Meztishura 29 February romantic movies on youtube Views: Likes: Sony lf pk1 manual lawn Magar 2 September clear midsummers night episode 1 recap Views: Likes: Share this: Twitter Facebook. Like this: Like Loading Next Post Next post: Download taraif asdi9ae film marocain.

Leave a Reply Cancel reply Enter your comment here Fill in your details below or click an icon to log in:. Email required Address never made public. Name required. Create your website with WordPress.