How to setup wireless network on samsung led tv

If your modem wasn't set up for you by your Internet service provider ISP , follow the instructions that came with your modem to connect it to your PC and the Internet. If you're using cable, connect your modem to a cable jack. Put your wireless router somewhere where it will receive the strongest signal with the least amount of interference. For better results, follow these tips:.

Place your wireless router in a central location. Place the router as close to the center of your home as possible to increase the strength of the wireless signal throughout your home. Position the wireless router off the floor and away from walls and metal objects , such as metal file cabinets. The fewer physical obstructions between your PC and the router's signal, the more likely that you'll be using the router's full signal strength.

Reduce interference. Some networking equipment uses a 2. This is the same frequency as most microwaves and many cordless phones. If you turn on the microwave or get a call on a cordless phone, your wireless signal might be temporarily interrupted. You can avoid most of these issues by using a cordless phone with a higher frequency, such as 5.

Security is always important; with a wireless network, it's even more important because your network's signal could be broadcast outside your home. If you don't help secure your network, people with PCs nearby could access info stored on your network PCs and use your Internet connection. Change the default user name and password. This helps protect your router. Most router manufacturers have a default user name and password on the router and a default network name also known as the SSID.

Someone could use this info to access your router without you knowing it. I'm going to show you how to set up a Network Extender and review some tips to help you get the most out of your device. So let's get started. Make sure you have the following:. Setup is complete when all 4 LED lights on the device are blue. This usually takes up to an hour, but can range from 15 minutes to 3 hours based on GPS signal strength. A strong GPS signal not only helps reduce setup time, but it's required for continuous operation of the Network Extender and provides your location to emergency responders if you call For best results with GPS signal strength, place the Network Extender as close to a window as possible.

If you're not able to place the device near a window and it's taking more than an hour to establish a GPS signal, use the included 23 foot GPS extension cable.

To do this, remove the antenna cover on top of the device, then remove the antenna and connect it to the end of the extension cable labeled "GPS antenna" and plug the other end of the cable to the Network Extender. Next, connect the Ethernet cable to your router and Network Extender.

Then, plug in the power supply. The 4 LED lights will start to flash. Let's talk about each of them in more detail:. If the System LED is blinking red fast for more than 3 minutes, it may be due to your router.

Try plugging the cable directly into your modem instead of the back of the router to see if that works. If it does then you know the issue is due to your router's settings. For assistance, contact your Internet Service Provider or go to our support page. If the light is red or blinking red for more than 15 minutes, move the Network Extender next to a window or use the GPS extension cable. Now that all four lights are solid blue, there are 2 tips to know before making a call.

You must be within 15 feet for 3 minutes to establish an initial connection with the Network Extender. This is required every time you enter your home. After a connection is made, you can move up to 40 feet away. If you have a phone with Advanced Calling activated and in a location with weak 4G signal, turn the feature off from your phone to connect with the Network Extender. Here's how you know if you're connected to the Network Extender.

Now take a look at a few tips and important information for reference. You can set up prioritized users for the Network Extender.

Log onto My Verizon, and enter Network Extender in the search box. Voice, messaging and data usage will be billed based on your rate plan while connected to the Network Extender.

To better manage your data usage, connect your mobile device to your Wi-Fi network. This way only voice and messaging rates will be used.

Thanks for watching and have a great day. Accessibility Resource Center Skip to main content. Darlene has experience teaching college courses, writing technology-related articles, and working hands-on in the technology field.

She earned an MA in Writing from Rowan University in and wrote her thesis on online communities and the personalities curated in such communities. This article has been viewed 18, times. You need to have a Wi-Fi network set up to do this.

Press Menu on your remote. Navigate to Network. Navigate to Network connection and press Select. Navigate to Quick setup and press Select. Navigate to your network and press Select. Enter your network password then press Back or Return. Press Select. Did this summary help you? Yes No. Log in Social login does not work in incognito and private browsers.

Please log in with your username or email to continue. No account yet? Create an account. But tomorrow it was back to the same. Do I do this everyday. Drew Hackelman. The only thing that really worked was to stop using WiFi and plug our smarthub into our router via Ethernet cable…. Fix Your Stuff Community Store. Back Answers Index. Makendlas Rep: 25 1 1. View the answer I have this problem too Subscribed to new answers. Is this a good question? Yes No. Voted Undo. Score 2. Did the above recommendations work??